ROOT LOCUS. Consider the system. Root locus presents the poles of the closedloop system when the gain K changes from 0 to. H(s) H ( s) = ( s)


 Oswin Burke
 3 years ago
 Views:
Transcription
1 C1 ROOT LOCUS Consider the system R(s) E(s) C(s) + K G(s)  H(s) C(s) R(s) = K G(s) 1 + K G(s) H(s) Root locus presents the poles of the closedloop system when the gain K changes from 0 to 1+ K G ( s) H ( s) = 0 { K G( s) H ( s) = 1 Magnitude Condition, G( s) H ( s) =± 180 (2k + 1) k= 0,1,2, Angle Condition
2 C2 Example: K G(s) H(s) = K s (s + 1) 1 + K G(s) H(s) = 0 s 2 + s + K = 0 s 1,2 = 1 2 ± K Angle condition: K = s s + 1= (180 θ ) θ2 = s ( s + 1) 1 ±, 180 splane K=1 θ 2 θ 1 K=01 K=1/4 K=0
3 C3 Magnitude and Angle Conditions K G(s) H(s) = K (s + z 1 ) (s + p 1 ) (s + p 2 ) (s + p 3 ) (s + p 4 ) K G(s) H(s) = K B 1 A 1 A 2 A 3 A 4 = 1 G(s) H(s) = ϕ 1 θ 1 θ 2 θ 3 θ 4 = ±180, (2 k +1) for k = 0, 1, 2,
4 C4 Construction Rules for Root Locus Openloop transfer function: K H(s) G(s) = K B(s) A(s) m: order of openloop numerator polynomial n: order of openloop denominator polynomial Rule 1: Number of branches The number of branches is equal to the number of poles of the openloop transfer function. Rule 2: Realaxis root locus If the total number of poles and zeros of the openloop system to the right of the spoint on the real axis is odd, then this point lies on the locus. Rule 3: Root locus endpoints The locus starting point ( K=0 ) are at the openloop poles and the locus ending points ( K= ) are at the open loop zeros and nm branches terminate at infinity.
5 C5 Rule 4: Slope of asymptotes of root locus as s approaches infinity I m Asymptote γ Real σ a γ = ±180 (2k + 1), k = 0,1,2,... n m Rule 5: Abscissa of the intersection between asymptotes of root locus and realaxis σ a= n ( pi ) n m m i= 1 i= 1 ( zi ) ( p i ) = poles of openloop transfer function ( z i ) = zeros of openloop transfer function
6 C6 Rule 6: Breakaway and breakin points From the characteristic equation f()= s A(s) + K B(s) = 0 the breakaway and in points can be found from: dk ds = A' (s) B(s) A(s) B ' (s) B 2 (s) = 0 Rule 7: Angle of departure from complex poles or zeros Subtract from 180 the sum of all angles from all other zeros and poles of the openloop system to the complex pole (or zero) with appropriate signs. Rule 8: Imaginaryaxis crossing points Find these points by solving the characteristic equation for s=jω or by using the Routh s table.
7 C7 Rule 9: Conservation of the sum of the system roots If the order of numerator is lower than the order of denominator by two or more, then the sum of the roots of the characteristic equation is constant. Therefore, if some of the roots more towards the left as K is increased, the other roots must more toward the right as K in increased.
8 C8 Discussion of Root Locus Construction Rules Consider: R(s) E(s) C(s) + K G(s)  H(s) K H ( s) G( s) = K B( s) A( s) = K m i= 0 n i= 0 b i s α s i m i n i m: number of zeros of openloop KH(s)G(s) n: number of poles of openloop KH(s)G(s) Characteristic Equation: f()= s A(s) + K B(s) = 0
9 C9 Rule 1: Number of branches The characteristic equation has n zeros the root locus has n branches Rule 2: Realaxis root locus ϕ 4 ϕ 3 s 2 ϕ 2 s 1 ϕ 1 ϕ 5 Consider two points s 1 and s 2 : s 1 { ϕ1 =180, ϕ2 = 0 = ϕ3 ϕ1+ϕ2 ϕ3+ϕ4 +ϕ5 = 3 180, ϕ 4+ϕ5 = s ϕ1 =180, ϕ2 = 180, ϕ3=0, ϕ4 +ϕ5 = { ϕ1+ϕ2 ϕ3+ϕ4+ϕ5 = Therefore, s 1 is on the root locus; s 2 is not.
10 C10 Rule 3: Root locus endpoints Magnitude condition: B(s) A(s) K=0 open loop poles = K= m open loop zeros 1 K = mn branches approach infinity m i = 1 n i = 1 (s + z i ) (s + p i ) Rule 4: Slope of asymptotes of root locus as s approaches infinity K B(s) A(s) = 1 lim K B(s) s A(s) = lim K s s n m = 1 s n m Using the angle condition: s m n, = K = ± 180 (2 k + 1) = K for s, k = 1, 2, 3, or
11 C11, ( n m) s = ± 180 (2 k + 1) leading to s = γ = ±180, (2 k +1) n m Rule 5: Abscissa of the intersection between asymptotes of rootlocus and real axis A(s) B(s) = s n + s n 1 p i n i = 1 m s m + s m 1 z i i = 1 m p i i = 1 n z i i = 1 = K Dividing numerator by denominator yields: s n m m z i i = 1 n p i i = 1 s n m = K For large values of s this can be approximated by: m n z i i = 1 s n m p i i = 1 n m = K The equation for the asymptote (for s ) was found in Rule 4 as
12 C12 s n m = K this implies σ a = m zi + n pi pi i= 1 i= 1 i= 1 i= 1 = n m n m n m zi Rule 6: Breakaway and breakin points At breakaway (and breakin) points the characteristic equation: f(s) = A(s) + K B(s) = 0 has multiple roots such that: df (s) ds = 0 A ' (s) + K B ' (s) = 0 A ' (s) = da(s) ds for K = A ' (s) B ' (s), f(s) has multiple roots Substituting the above equation into f(s) gives: A(s) B ' (s) A ' (s) B(s) = 0
13 C13 Another approach is using: This gives: K = A(s) B(s) from f()= s 0 dk (s) B(s) A(s) B ' (s) ds = A' B 2 (s) and breakaway, breakin points are obtained from: dk ds = 0 Extended Rule 6: Consider and f(s) = A(s) + K B(s) = 0 K = A(s) B(s) If the first (y1) derivatives of A(s)/B(s) vanish at a given point on the root locus, then there will be y branches approaching and y branches leaving this point. The angle between two adjacent approaching branches is given by: θ y = ± 360, y
14 C14 The angle between a leaving branch and an adjacent approaching branch is: θ y = ± 180, y Rule 7: Angle of departure from complex pole or zero θ 3 θ 2 = 90, ϕ 1 θ 1 θ 3 = 180, (θ 1 +θ 2 ϕ 1 ) θ 2 Rule 8: Imaginaryaxis crossing points Example: f (s) = s 3 + b s 2 + c s + K d = 0 s 3 1 c s 2 b Kd s 1 (bckd)/b s 0 Kd s 1,2 = ± j K d b For crossing points on the Imaginary axis: b c K d = 0 K = bc d Further, b s 2 + K d = 0 leading to = ± jω
15 C15 The same result is obtained by solving f(jω) = 0. Rule 9: Conservation of the sum of the system roots From = + = + n i r i s s B K s A 1 ) ( ) ( ) ( we have ) ( ) ( ) ( = = = + = n i m i n i i i i r s r s K p s with = + = n i p i s s A 1 ) ( ) ( and = + = m i z i s s B 1 ) ( ) ( By equating coefficients of s n 1 for n m + 2, we obtain the following: = = = n i i n i p i r 1 1 i.e. the sum of closedloop poles is independent of K! Sum of openloop poles Sum of closedloop poles
16 C16
17 C17 Effect of Derivative Control and Velocity Feedback Consider the following three systems: Positional servo. Closedloop poles: s = 0.1 ± j Positional servo with derivative control. Closedloop poles: s = 0.5 ± j Positional servo with velocity feedback. Closedloop poles: s = 0.5 ± j Openloop of system I: G I (s) = 5 s ( 5 s + 1) Openloop of systems II and III: G(s) = 5 (1+ 0.8s) s ( 5 s + 1)
18 C18 Root locus for the three systems jω j X X 0 j1 σ a) System I Closedloop zero jω j X X 0 j1 σ b) System II
19 C19 Openloop zero jω j X X 0 j1 σ c) System III Closedloop zeros: System I: System II: System III: none 1+0.8s=0 none Observations: The root locus presents the closed loop poles but gives no information about closedloop zeros. Two system with same root locus (same closedloop poles) may have different responses due to different closedloop zeros.
20 C20 Unitstep response curves for systems I,II and III : The unitstep response of system II is the fastest of the three. This is due to the fact that derivative control responds to the rate of change of the error signal. Thus, it can produce a correction signal before the error becomes large. This leads to a faster response.
21 C21 Conditionally Stable Systems System which can be stable or unstable depending on the value of gain K. R(s) +  K G(s) C(s) O unstable X X X X O stable X unstable Minimum Phase Systems All poles and zeros are in the left half plane.
22 C22 Frequency Response Methods x(t) G(s) y(t) x(t) = X sin(ω t) X(s) = ω X s 2 + ω 2 Y(s) = G(s) X(s) = G(s) a = a = X(s) y(t) = ae j ω t Y(s) ω X s 2 + ω 2 = + a e j ω t a s + jω + a s jω + + b i e s i t i stable system Re( s i ) < 0 for all i for t y(t) = ae jω t + a e jω t ω X G(s) s 2 +ω 2 s+ jω ( ) = ω X G(s) s 2 +ω 2(s jω) = ( s= jω) (s= j ω) XG( j ω) 2j XG(jω) 2j i b i s + s i
23 C23 and G( jω ) = G( j ω) e j ϕ G( jω ) = G(j ω) e j ϕ ϕ = tan 1 Im(G( j ω)) Re( G( j ω)) y(t) = X G( j ω) ej(ωt+ϕ) e j(ωt+ϕ) = Y sin(ωt +ϕ 2j ϕ > 0 phase lag ϕ < 0 phase lead G( jω ) = Y( j ω) X( jω ) G( j ω) = Y(j ω) X( j ω) Magnitude response ϕ = (G(j ω)) = Y( j ω) X( jω ) Phase response
24 C24 Connection between pole locations and Frequency Response G(s) = K(s + z) s(s + p) G( jω) = K jω + z jω jω + p G(jω ) = ϕ θ 1 θ 2 Frequency Response Plots Bode Diagrams Polar Plots (Nyquist Plots) LogMagnitudeVersusPhase Plots (Nichols Plots)
25 C25 Bode Diagrams Magnitude response G( jω) 20 log G( jω) in db Phase response G(jω) in degrees Basic factors of G(jω): Gain K Integral or derivative factors ( jω) ±1 Firstorder factors Quadratic factors (1 + jωt ) ± 1 ± 1 2 jω jω 1+ 2 j + ω n n ω 1. Gain Factor K Horizontal straight line at magnitude 20 log(k) db Phase is zero
26 C26 2. Integral or derivative factors ( jω) ± 1 ( jω ) 1 ( jω ) 20 log 1 jω = 20 logω magnitude: straight line with slope 20 db/decade phase: 90 o 20 log jω = 20logω magnitude: straight line with slope 20 db/decade phase: +90 o
27 C27 3. First order factors (1+ jω T) ± 1 (1+ jω T) 1 Magnitude: 1 2 T 2 20 log = 20 log 1 + ω 1 + jωt db for ω << T 1 0 db magnitude for ω >> T 1 20log( ω T) db magnitude Approximation of the magnitude: for ω between 0 and ω = 1 T 0 db for ω >> 1 T straight line with slope 20 db /decade Phase: (1+ jω T) 1 = tan 1 (ωt ) for ω = 0 ϕ = 0, 1 1 T for ω = tan = 1 ϕ = 45, T T for ω = ϕ = 90,
28 C28 (1+ jω T) + 1 Using 20 log 1+ jω T = 20log jω T (1+ jω T) = tan 1 ( ω T) = jω T
29 C29 4. Quadratic Factors ) ( + + = n n j j j G ω ω ω ω ς ω 1 0 < <ς Magnitude: 20 log G( jω) = 20 log 1 ω 2 ω 2 n 2 2 j ω ω n 2 for ω << ω n 0 db for ω >> ω n 20 log ω 2 ω 2 n = 40log ω ω n db Phase: = = tan ) ( tan n n j G ω ω ω ω ς ω ϕ Resonant Frequency: ς ω ω = n T Resonant Peak Value: 2 max ) ( ς ξς ω = = j G M T
30 C30 Example: G( jω ) = 10( jω + 3) jω ( ) jω + 2 ( ) jω ( ) 2 + jω + 2 ( ) ( ) ( ) = ) ( 2 ω ω ω ω ω ω j j j j j j G
31 C31
32 C32 Frequency Response of nonminimum Phase systems Minimum phase systems have all poles and zeros in the left half splane and were discussed before Consider then A 1 (s) = 1+ Ts A 2 (s) = 1 Ts A 3 (s)= Ts 1 A 1 (jω) = A 2 (jω) = A 3 (jω) A 2 (jω) = A 1 (jω) A 3 (jω) = 180 A 1 (jω) We know that phase of A 1 (jω) from 0 o to +90 o Æ phase of A 2 (jω) from 0 o to 90 o phase of A 3 (jω) from 180 o to +90 o
33 C33 Phaseangle characteristic of the two systems G 1 (s) and G 2 (s) having the same magnitude response but G 1 (s) is minimum phase while G 2 (s) is not. Frequency Response of Unstable Systems Consider then 1 G 1 (s) = 1 + Ts G 2 (s) = 1 1 Ts 1 G 3 (s) = Ts 1 G 1 (jω) = G 2 (jω) = G 3 (jω) G 2 (jω) = G 1 (jω) G 3 (jω) = 180 o G 1 (jω) We know that phase of G 1 (jω) from 0 o to 90 o Æ phase of G 2 (jω) from 0 o to +90 o phase of G 3 (jω) from 180 o to 90 o
34 C34 Relationship between System Type and Log Magintude curve Type of system determines: the slope of the logmagnitude curve at low frequencies for minimum phase, also the phase at low frequencies Type 0 Position Error Coefficient K p 0 Slope at low frequencies: 0 db/decade Phase at low frequencies (minimum phase): 0 o lim G( jω) = K p ω 0
35 C35 Type 1 Velocity Error Coefficient K v 0 (K p = ) K v = lim jω G( jω ) ω 0 G(jω ) = K v jω for ω << 20log K v = 20log K v jω for ω = 1 Slope at low frequencies: 20 db/decade Phase at low frequencies (minimum phase): 90 o
36 C36 Type 2 Acceleration Error Coefficient K a K a 2 ( jω ) G( j ) 0 = lim ω ω 0 (K p = K v = ) K G(jω ) = a (jω ) 2 for ω << 1 20logK a = 20log K a ( jω ) 2 for ω = 1 Slope at low frequencies: 40 db/decade Phase at low frequencies (minimum phase): 180 o
37 C37 Polar Plots (Nyquist Plots) G( jω ) = G( jω ) G( jω ) = Re[ G( jω )]+ Im[ G( jω )] Advantage over Bode plots: only one plot Disadvantage : Polar plot of G( jω) = G1 ( jω) G2( jω) is more difficult to construct than its Bode plot. Basic factors of G(jω): Integral or derivative factors ( jω) ± 1 G( jω ) = 1 jω = j 1 ω = G(jω ) = jω = ω 90, 1 ω 90,
38 C38 First order factors (1+ jω T) ± 1 X = G( jω ) = jω T = X + jy 1 1+ ω 2 T 2, Y = ω T 1 +ω 2 T 2 It can be show that (X 0.5) 2 + Y 2 = (0.5) 2 Polar plot is a circle with Center (1/2, 0) and Radius 0.5.
39 C39 Quadratic Factors G( jω) = 1+ 2ζ 1 ω jω j + ωn ωn 2 1 >ζ >0 lim ω 0 G( jω ) = 1 0, lim G(jω) = 0 180, ω 1, G( jωn) = 90 j2 ς
40 C n n j j ω ω ω ω ς lim ω 0 G( jω ) = 1 0, lim ω G(jω) = 180,
41 C41 General shapes of polar plots K(1 + jωt )...(1 ) ( ) 1 + jωt G jω = m λ ( jω) (1 + jωtλ+ 1)...(1 + jωtn ) n = order of the system (denominator) λ = type of system λ > 0 m = order of numerator n > m For low frequencies: The phase at ω 0 is λ ( 90 ), For system type 1, the low frequency asymptote is obtained by taking: Re[ G( jω )] for ω 0 For high frequencies: The phase is: (n  m) ( 90 o )
42 C42
43 LogMagnitudeVersusPhase Plots (Nichols Plots) C43
44 C44 Example: Frequency Response of a quadratic factor The same information presented in three different ways: Bode Diagram Polar Plot LogMagnitudeVersusPhase Plots
45 Nyquist Stability Criterion C45 The Nyquist stability criterion relates the stability of the closed loop system to the frequency response of the openloop system. R(s) +  G(s) C(s) H(s) Openloop: Closedloop: G() s H() s G() s 1+ Gs () Hs () Advantages of the Nyquist Stability Criterion: Simple graphical procedure to determine whether a system is stable or not The degree of stability can be easily obtained Easy for compensator design The response for steadystate sinusoidal inputs can be easily obtained from measurements
46 C46 Preview Mathematical Background Mapping theorem Nyquist path Nyquist stability criterion Z=N+P Z: Number of zeros of (1+H(s)G(s)) in the right half plane = number of unstable poles of the closedloop system N: Number of clockwise encirclements of the point 1+j0 P: Number of poles of G(s)H(s) in the right half plane Application of the Stability Criterion Sketch the Nyquist plot for ω (0 +, ) Extend to ω (,+ ) Apply the stability criterion (find N and P and compute Z).
47 C47 Mapping Theorem The total number N of clockwise encirclements of the origin of the F(s) plane, as a representative point s traces out the entire contour in the clockwise direction, is equal to Z P. F(s) = A(s) Q(s) P: Number of poles, Q(s) = 0 Z: Number of zeros, A(s) = 0 VSODQH )V SODQH FRQWRXU [ )V R [ R R [ [ ]HURV $V SROHV 4V
48 C48 Mapping for F(s) = s/(s+0.5), (Z = P =1) Example of Mapping theorem (Z P = 2). Example of Mapping theorem (Z P =  1).
49 C49 Application of the mapping theorem to stability analysis Mω VSODQH )V SODQH 5 1\TXLVW SDWK WKH FRPSOHWH ULJKW KDOI SODQH LV HQFORVHG LQVLGH WKH SDWK Mω )V *V+ V Mapping theorem: The number of clockwise encirclements of the origin is equal to the difference between the zeros and poles of F(s) = 1+ G(s)H(s). Zeros of F(s) = poles of closedloop system Poles of F(s) = poles of openloop system
50 C50 Frequency response of openloop system: G(jω)H(jω) +jω splane F(s)(=1+G(s)H(s))plane G(s)H(s)plane Im R= 1+G(jω)H(jω) Re G(jω)H(jω) jω F(s)=1+G(s)H(s) Frequency response of a type 1 system
51 C51 Nyquist stability criterion Consider R(s) +  G(s) C(s) H(s) The Nyquist stability criterion states that: Z = N + P Z: Number of zeros of 1+H(s)G(s) in the right half splane = number of poles of closedloop system in right half s plane. N: Number of clockwise encirclements of the point 1+j0 (when tracing from ω =  to ω = + ). P: Number of poles of G(s)H(s) in the right half splane Thus: if Z = 0 closedloop system is stable if Z > 0 closedloop system has Z unstable poles if Z < 0 impossible, a mistake has been made
52 Alternative form for the Nyquist stability criterion: C52 If the openloops system G(s)H(s) has k poles in the right half splane, then the closedloop system is stable if and only if the G(s)H(s) locus for a representative point s tracing the modified Nyquist path, encircles the 1+j0 point k times in the counterclockwise direction. Frequency Response of G(jω)H(jω) for ω : (,+ ) a) ω : (0 +,+ ) : using the rules discussed earlier b) ω : (0 , ) : G(jω)H(jω) is symmetric with G(jω)H(jω) (real axis is symmetry axis) c) ω : (0 ,0 + ) : next page
53 Poles at the origin for G(s)H(s): C53 G() s Hs ()= (...) s λ (...) If G(s)H(s) involves a factor 1, then the plot of G(jω)H(jω), s λ for ω between 0  and 0 +, has λ clockwise semicircles of infinite radius about the origin in the GH plane. These semicircles correspond to a representative point s moving along the Nyquist path with a semicircle of radius ε around the origin in the s plane.
54 Relative Stability C54 Consider a modified Nyquist path which ensures that the closedloop system has no poles with real part larger than σ 0 : Another possible modified Nyquist path:
55 Phase and Gain Margins C55 A measure for relative stability of the closedloop system is how close G(jω), the frequency response of the openloop system, comes to 1+j0 point. This is represented by phase and gain margins. Phase margin: The amount of additional phase lag at the Gain Crossover Frequency ω o required to bring the system to the verge of instability. Gain Crossover Frequency: ω o for which G jωo = 1 Phase margin: γ = G(jω o ) = φ Gain margin: The reciprocal of the magnitude G jω at the 1 Phase Crossover Frequency ω 1 required to bring the system to the verge of instability. Phase Crossover Frequency: ω 1 where G jω 1 = 180, Gain margin: K 1 g = G( jω ) 1 Gain margin in db: K g in db= 20logG jω 1 K g in db > 0 = stable (for minimum phase systems) K g in db < 0 = unstable (for minimum phase systems)
56 C56 Figure: Phase and gain margins of stable and unstable systems (a) Bode diagrams; (b) Polar plots; (c) Logmagnitudeversusphase plots.
57 C57 If the openloop system is minimum phase and has both phase and gain margins positive, Æ then the closedloop system is stable. For good relative stability both margins are required to be positive. Good values for minimum phase system: Phase margin : Gain margin: above 6 db
58 C58 Correlation between damping ratio and frequency response for 2 nd order systems R(s) +  s ω n ( s + 2ζω ) n C(s) C R 2 () s ωn () s 2 2 Phase margin: = C jω s + 2ζωns + ωn R jω ( ) ( ) = M ω jα ω ( ) e ( ) γ = G(jω) G(jω): open loop transfer function G ( jω) = jω ω 2 n ( jω + 2ζω ) n becomes unity for ω = ω n 1 + 4ζ 2ζ and 1 2ζω 1 γ = tan n = tan ω1 2ζ ζ 2ζ Æ γ depends only on ζ
59 C59 Performance specifications in the frequency domain: 0dB M r 3dB ω r ωc ω c : ω c : Cutoff Frequency 0 ω ω c : Bandwidth Slope of logmagnitude curve: Cutoff Rate ability to distinguish between signal and noise ω r : Resonant Frequency indicative of transient response speed ω r Æ increase, transient response faster (dominant complex conjugate poles assumed) M r = max G(jω) : Resonant Peak
60 C60 ClosedLoop Frequency Response Openloop system: G(s) Stable closedloop system: C( s) = G( s) R( s) 1+ G( s) R(s) +  G(s) C(s) Gs () 1+Gs = () OA PA
61 ClosedLoop Frequency Response: C61 ( ) ( ) = G jω C jω Rjω ( ) 1+G( jω ) = M ejα Constant Magnitude Loci: ( jω ) = X jy G + X + jy M = = const 1 + X + jy X + M2 M Y 2 = M 2 M Constant PhaseAngle Loci G ( jω ) = X + jy Æ e jα = X + jy 1+ X + jy = const 2 2 X Y + 1 2N = N 2, N = tanα
62 Figure: A family of constant M circles. C62
63 C63 Figure: (a) G(jω) locus superimposed on a family of M circles; (b) G(jω) locus superimposed om a family of N circles; (c) Closedloop frequencyresponse curves
64 C64 Experimental Determination of Transfer Function Derivation of mathematical model is often difficult and may involve errors. Frequency response can be obtained using sinusoidal signal generators. Measure the output and obtain: Magnitudes (quite accurate) Phase (not as accurate) Use the Magnitude data and asymptotes to find: Type and error coefficients Corner frequencies Orders of numerator and denominator If second order terms are involved, ζ is obtained from the resonant peak. Use phase to determine if system is minimum phase or not: Minimum phase: ωæ phase = 90 (n  m) (nm) difference in the order of denominator and numerator.
Homework 7  Solutions
Homework 7  Solutions Note: This homework is worth a total of 48 points. 1. Compensators (9 points) For a unity feedback system given below, with G(s) = K s(s + 5)(s + 11) do the following: (c) Find the
More informationRadar Dish. Armature controlled dc motor. Inside. θ r input. Outside. θ D output. θ m. Gearbox. Control Transmitter. Control. θ D.
Radar Dish ME 304 CONTROL SYSTEMS Mechanical Engineering Department, Middle East Technical University Armature controlled dc motor Outside θ D output Inside θ r input r θ m Gearbox Control Transmitter
More informationFrequency Response Techniques
4th Edition T E N Frequency Response Techniques SOLUTION TO CASE STUDY CHALLENGE Antenna Control: Stability Design and Transient Performance First find the forward transfer function, G(s). Pot: K 1 = 10
More informationLecture 6 Classical Control Overview IV. Dr. Radhakant Padhi Asst. Professor Dept. of Aerospace Engineering Indian Institute of Science  Bangalore
Lecture 6 Classical Control Overview IV Dr. Radhakant Padhi Asst. Professor Dept. of Aerospace Engineering Indian Institute of Science  Bangalore Lead Lag Compensator Design Dr. Radhakant Padhi Asst.
More informationINTRODUCTION TO DIGITAL CONTROL
ECE4540/5540: Digital Control Systems INTRODUCTION TO DIGITAL CONTROL.: Introduction In ECE450/ECE550 Feedback Control Systems, welearnedhow to make an analog controller D(s) to control a lineartimeinvariant
More informationModule 3F2: Systems and Control EXAMPLES PAPER 2 ROOTLOCUS. Solutions
Cambridge University Engineering Dept. Third Year Module 3F: Systems and Control EXAMPLES PAPER ROOTLOCUS Solutions. (a) For the system L(s) = (s + a)(s + b) (a, b both real) show that the rootlocus
More informationLecture 5: Frequency domain analysis: Nyquist, Bode Diagrams, second order systems, system types
Lecture 5: Frequency domain analysis: Nyquist, Bode Diagrams, second order systems, system types Venkata Sonti Department of Mechanical Engineering Indian Institute of Science Bangalore, India, 562 This
More informationMAS107 Control Theory Exam Solutions 2008
MAS07 CONTROL THEORY. HOVLAND: EXAM SOLUTION 2008 MAS07 Control Theory Exam Solutions 2008 Geir Hovland, Mechatronics Group, Grimstad, Norway June 30, 2008 C. Repeat question B, but plot the phase curve
More information8.1.6 Quadratic pole response: resonance
8.1.6 Quadratic pole response: resonance Example G(s)= v (s) v 1 (s) = 1 1+s L R + s LC L + Secondorder denominator, of the form 1+a 1 s + a s v 1 (s) + C R Twopole lowpass filter example v (s) with
More informationIC6501 CONTROL SYSTEMS
DHANALAKSHMI COLLEGE OF ENGINEERING CHENNAI DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING YEAR/SEMESTER: II/IV IC6501 CONTROL SYSTEMS UNIT I SYSTEMS AND THEIR REPRESENTATION 1. What is the mathematical
More informationSoftware Engineering 3DX3. Slides 8: Root Locus Techniques
Software Engineering 3DX3 Slides 8: Root Locus Techniques Dr. Ryan Leduc Department of Computing and Software McMaster University Material based on Control Systems Engineering by N. Nise. c 2006, 2007
More information1 (s + 3)(s + 2)(s + a) G(s) = C(s) = K P + K I
MAE 43B Linear Control Prof. M. Krstic FINAL June 9, Problem. ( points) Consider a plant in feedback with the PI controller G(s) = (s + 3)(s + )(s + a) C(s) = K P + K I s. (a) (4 points) For a given constant
More informationDelhi Noida Bhopal Hyderabad Jaipur Lucknow Indore Pune Bhubaneswar Kolkata Patna Web: Ph:
Serial : 0. LS_D_ECIN_Control Systems_30078 Delhi Noida Bhopal Hyderabad Jaipur Lucnow Indore Pune Bhubaneswar Kolata Patna Web: Email: info@madeeasy.in Ph: 04546 CLASS TEST 089 ELECTRONICS ENGINEERING
More informationRoot Locus Methods. The root locus procedure
Root Locus Methods Design of a position control system using the root locus method Design of a phase lag compensator using the root locus method The root locus procedure To determine the value of the gain
More informationIntroduction to Root Locus. What is root locus?
Introduction to Root Locus What is root locus? A graphical representation of the closed loop poles as a system parameter (Gain K) is varied Method of analysis and design for stability and transient response
More informationFREQUENCY RESPONSE ANALYSIS Closed Loop Frequency Response
Closed Loop Frequency Response The Bode plot is generally constructed for an open loop transfer function of a system. In order to draw the Bode plot for a closed loop system, the transfer function has
More informationSystems Analysis and Control
Systems Analysis and Control Matthew M. Peet Arizona State University Lecture 21: Stability Margins and Closing the Loop Overview In this Lecture, you will learn: Closing the Loop Effect on Bode Plot Effect
More informationThe Nyquist criterion relates the stability of a closed system to the openloop frequency response and open loop pole location.
Introduction to the Nyquist criterion The Nyquist criterion relates the stability of a closed system to the openloop frequency response and open loop pole location. Mapping. If we take a complex number
More informationSchool of Mechanical Engineering Purdue University. DC Motor Position Control The block diagram for position control of the servo table is given by:
Root Locus Motivation Sketching Root Locus Examples ME375 Root Locus  1 Servo Table Example DC Motor Position Control The block diagram for position control of the servo table is given by: θ D 0.09 See
More informationThe Frequencyresponse Design Method
Chapter 6 The Frequencyresponse Design Method Problems and Solutions for Section 6.. (a) Show that α 0 in Eq. (6.2) is given by α 0 = G(s) U 0ω = U 0 G( jω) s jω s= jω 2j and α 0 = G(s) U 0ω = U 0 G(jω)
More informationTransient response via gain adjustment. Consider a unity feedback system, where G(s) = 2. The closed loop transfer function is. s 2 + 2ζωs + ω 2 n
Design via frequency response Transient response via gain adjustment Consider a unity feedback system, where G(s) = ωn 2. The closed loop transfer function is s(s+2ζω n ) T(s) = ω 2 n s 2 + 2ζωs + ω 2
More informationCHAPTER 7 : BODE PLOTS AND GAIN ADJUSTMENTS COMPENSATION
CHAPTER 7 : BODE PLOTS AND GAIN ADJUSTMENTS COMPENSATION Objectives Students should be able to: Draw the bode plots for first order and second order system. Determine the stability through the bode plots.
More informationLecture 1 Root Locus
Root Locus ELEC304Alper Erdogan 1 1 Lecture 1 Root Locus What is RootLocus? : A graphical representation of closed loop poles as a system parameter varied. Based on RootLocus graph we can choose the
More informationControls Problems for Qualifying Exam  Spring 2014
Controls Problems for Qualifying Exam  Spring 2014 Problem 1 Consider the system block diagram given in Figure 1. Find the overall transfer function T(s) = C(s)/R(s). Note that this transfer function
More informationEC6405  CONTROL SYSTEM ENGINEERING Questions and Answers Unit  I Control System Modeling Two marks 1. What is control system? A system consists of a number of components connected together to perform
More informationKINGS COLLEGE OF ENGINEERING DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
KINGS COLLEGE OF ENGINEERING DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING QUESTION BANK SUB.NAME : CONTROL SYSTEMS BRANCH : ECE YEAR : II SEMESTER: IV 1. What is control system? 2. Define open
More informationDESIGN USING TRANSFORMATION TECHNIQUE CLASSICAL METHOD
206 Spring Semester ELEC733 Digital Control System LECTURE 7: DESIGN USING TRANSFORMATION TECHNIQUE CLASSICAL METHOD For a unit ramp input Tz Ez ( ) 2 ( z ) D( z) G( z) Tz e( ) lim( z) z 2 ( z ) D( z)
More informationEC CONTROL SYSTEM UNIT I CONTROL SYSTEM MODELING
EC 2255  CONTROL SYSTEM UNIT I CONTROL SYSTEM MODELING 1. What is meant by a system? It is an arrangement of physical components related in such a manner as to form an entire unit. 2. List the two types
More informationELECTRONICS & COMMUNICATIONS DEP. 3rd YEAR, 2010/2011 CONTROL ENGINEERING SHEET 5 LeadLag Compensation Techniques
CAIRO UNIVERSITY FACULTY OF ENGINEERING ELECTRONICS & COMMUNICATIONS DEP. 3rd YEAR, 00/0 CONTROL ENGINEERING SHEET 5 LeadLag Compensation Techniques [] For the following system, Design a compensator such
More information7.4 STEP BY STEP PROCEDURE TO DRAW THE ROOT LOCUS DIAGRAM
ROOT LOCUS TECHNIQUE. Values of on the root loci The value of at any point s on the root loci is determined from the following equation G( s) H( s) Product of lengths of vectors from poles of G( s)h( s)
More informationIf you need more room, use the backs of the pages and indicate that you have done so.
EE 343 Exam II Ahmad F. Taha Spring 206 Your Name: Your Signature: Exam duration: hour and 30 minutes. This exam is closed book, closed notes, closed laptops, closed phones, closed tablets, closed pretty
More informationRoot locus Analysis. P.S. Gandhi Mechanical Engineering IIT Bombay. Acknowledgements: Mr Chaitanya, SYSCON 07
Root locus Analysis P.S. Gandhi Mechanical Engineering IIT Bombay Acknowledgements: Mr Chaitanya, SYSCON 07 Recap R(t) + _ k p + k s d 1 s( s+ a) C(t) For the above system the closed loop transfer function
More informationCHAPTER # 9 ROOT LOCUS ANALYSES
F K א CHAPTER # 9 ROOT LOCUS ANALYSES 1. Introduction The basic characteristic of the transient response of a closedloop system is closely related to the location of the closedloop poles. If the system
More informationFATIMA MICHAEL COLLEGE OF ENGINEERING & TECHNOLOGY
FATIMA MICHAEL COLLEGE OF ENGINEERING & TECHNOLOGY Senkottai Village, Madurai Sivagangai Main Road, Madurai  625 020. An ISO 9001:2008 Certified Institution DEPARTMENT OF ELECTRONICS AND COMMUNICATION
More informationControl of Manufacturing Processes
Control of Manufacturing Processes Subject 2.830 Spring 2004 Lecture #19 Position Control and Root Locus Analysis" April 22, 2004 The Position Servo Problem, reference position NC Control Robots Injection
More informationr +  FINAL June 12, 2012 MAE 143B Linear Control Prof. M. Krstic
MAE 43B Linear Control Prof. M. Krstic FINAL June, One sheet of handwritten notes (two pages). Present your reasoning and calculations clearly. Inconsistent etchings will not be graded. Write answers
More information(b) A unity feedback system is characterized by the transfer function. Design a suitable compensator to meet the following specifications:
1. (a) The open loop transfer function of a unity feedback control system is given by G(S) = K/S(1+0.1S)(1+S) (i) Determine the value of K so that the resonance peak M r of the system is equal to 1.4.
More informationPlan of the Lecture. Goal: wrap up lead and lag control; start looking at frequency response as an alternative methodology for control systems design.
Plan of the Lecture Review: design using Root Locus; dynamic compensation; PD and lead control Today s topic: PI and lag control; introduction to frequencyresponse design method Goal: wrap up lead and
More informationCourse Outline. Closed Loop Stability. Stability. Amme 3500 : System Dynamics & Control. Nyquist Stability. Dr. Dunant Halim
Amme 3 : System Dynamics & Control Nyquist Stability Dr. Dunant Halim Course Outline Week Date Content Assignment Notes 1 5 Mar Introduction 2 12 Mar Frequency Domain Modelling 3 19 Mar System Response
More informationChapter 2. Classical Control System Design. Dutch Institute of Systems and Control
Chapter 2 Classical Control System Design Overview Ch. 2. 2. Classical control system design Introduction Introduction Steadystate Steadystate errors errors Type Type k k systems systems Integral Integral
More informationLecture 5 Classical Control Overview III. Dr. Radhakant Padhi Asst. Professor Dept. of Aerospace Engineering Indian Institute of Science  Bangalore
Lecture 5 Classical Control Overview III Dr. Radhakant Padhi Asst. Professor Dept. of Aerospace Engineering Indian Institute of Science  Bangalore A Fundamental Problem in Control Systems Poles of open
More informationAlireza Mousavi Brunel University
Alireza Mousavi Brunel University 1 » Control Process» Control Systems Design & Analysis 2 OpenLoop Control: Is normally a simple switch on and switch off process, for example a light in a room is switched
More informationSystems Analysis and Control
Systems Analysis and Control Matthew M. Peet Illinois Institute of Technology Lecture 23: Drawing The Nyquist Plot Overview In this Lecture, you will learn: Review of Nyquist Drawing the Nyquist Plot Using
More informationH(s) = s. a 2. H eq (z) = z z. G(s) a 2. G(s) A B. s 2 s(s + a) 2 s(s a) G(s) 1 a 1 a. } = (z s 1)( z. e ) ) (z. (z 1)(z e at )(z e at )
.7 Quiz Solutions Problem : a H(s) = s a a) Calculate the zero order hold equivalent H eq (z). H eq (z) = z z G(s) Z{ } s G(s) a Z{ } = Z{ s s(s a ) } G(s) A B Z{ } = Z{ + } s s(s + a) s(s a) G(s) a a
More informationNyquist Criterion For Stability of Closed Loop System
Nyquist Criterion For Stability of Closed Loop System Prof. N. Puri ECE Department, Rutgers University Nyquist Theorem Given a closed loop system: r(t) + KG(s) = K N(s) c(t) H(s) = KG(s) +KG(s) = KN(s)
More informationSolutions to SkillAssessment Exercises
Solutions to SkillAssessment Exercises To Accompany Control Systems Engineering 4 th Edition By Norman S. Nise John Wiley & Sons Copyright 2004 by John Wiley & Sons, Inc. All rights reserved. No part
More informationECE 486 Control Systems
ECE 486 Control Systems Spring 208 Midterm #2 Information Issued: April 5, 208 Updated: April 8, 208 ˆ This document is an info sheet about the second exam of ECE 486, Spring 208. ˆ Please read the following
More informationTime Response Analysis (Part II)
Time Response Analysis (Part II). A critically damped, continuoustime, second order system, when sampled, will have (in Z domain) (a) A simple pole (b) Double pole on real axis (c) Double pole on imaginary
More informationThe FrequencyResponse
6 The FrequencyResponse Design Method A Perspective on the FrequencyResponse Design Method The design of feedback control systems in industry is probably accomplished using frequencyresponse methods
More informationStep input, ramp input, parabolic input and impulse input signals. 2. What is the initial slope of a step response of a first order system?
IC6501 CONTROL SYSTEM UNITII TIME RESPONSE PARTA 1. What are the standard test signals employed for time domain studies?(or) List the standard test signals used in analysis of control systems? (April
More informationFrequency methods for the analysis of feedback systems. Lecture 6. Loop analysis of feedback systems. Nyquist approach to study stability
Lecture 6. Loop analysis of feedback systems 1. Motivation 2. Graphical representation of frequency response: Bode and Nyquist curves 3. Nyquist stability theorem 4. Stability margins Frequency methods
More informationCONTROL SYSTEM STABILITY. CHARACTERISTIC EQUATION: The overall transfer function for a. where A B X Y are polynomials. Substitution into the TF gives:
CONTROL SYSTEM STABILITY CHARACTERISTIC EQUATION: The overall transfer function for a feedback control system is: TF = G / [1+GH]. The G and H functions can be put into the form: G(S) = A(S) / B(S) H(S)
More information1 (20 pts) Nyquist Exercise
EE C128 / ME134 Problem Set 6 Solution Fall 2011 1 (20 pts) Nyquist Exercise Consider a close loop system with unity feedback. For each G(s), hand sketch the Nyquist diagram, determine Z = P N, algebraically
More informationControl Systems I. Lecture 9: The Nyquist condition
Control Systems I Lecture 9: The Nyquist condition adings: Guzzella, Chapter 9.4 6 Åstrom and Murray, Chapter 9.1 4 www.cds.caltech.edu/~murray/amwiki/index.php/first_edition Emilio Frazzoli Institute
More informationControl Systems Engineering ( Chapter 8. Root Locus Techniques ) Prof. KwangChun Ho Tel: Fax:
Control Systems Engineering ( Chapter 8. Root Locus Techniques ) Prof. KwangChun Ho kwangho@hansung.ac.kr Tel: 027604253 Fax:027604435 Introduction In this lesson, you will learn the following : The
More informationEE C128 / ME C134 Fall 2014 HW 8  Solutions. HW 8  Solutions
EE C28 / ME C34 Fall 24 HW 8  Solutions HW 8  Solutions. Transient Response Design via Gain Adjustment For a transfer function G(s) = in negative feedback, find the gain to yield a 5% s(s+2)(s+85) overshoot
More informationControl Systems. Frequency Method Nyquist Analysis.
Frequency Method Nyquist Analysis chibum@seoultech.ac.kr Outline Polar plots Nyquist plots Factors of polar plots PolarNyquist Plots Polar plot: he locus of the magnitude of ω vs. the phase of ω on polar
More informationClass 13 Frequency domain analysis
Class 13 Frequency domain analysis The frequency response is the output of the system in steady state when the input of the system is sinusoidal Methods of system analysis by the frequency response, as
More information100 (s + 10) (s + 100) e 0.5s. s 100 (s + 10) (s + 100). G(s) =
1 AME 3315; Spring 215; Midterm 2 Review (not graded) Problems: 9.3 9.8 9.9 9.12 except parts 5 and 6. 9.13 except parts 4 and 5 9.28 9.34 You are given the transfer function: G(s) = 1) Plot the bode plot
More informationDynamic circuits: Frequency domain analysis
Electronic Circuits 1 Dynamic circuits: Contents Free oscillation and natural frequency Transfer functions Frequency response Bode plots 1 System behaviour: overview 2 System behaviour : review solution
More informationChapter 7 : Root Locus Technique
Chapter 7 : Root Locus Technique By Electrical Engineering Department College of Engineering King Saud University 1431143 7.1. Introduction 7.. Basics on the Root Loci 7.3. Characteristics of the Loci
More informationFrequency domain analysis
Automatic Control 2 Frequency domain analysis Prof. Alberto Bemporad University of Trento Academic year 20102011 Prof. Alberto Bemporad (University of Trento) Automatic Control 2 Academic year 20102011
More informationVALLIAMMAI ENGINEERING COLLEGE SRM Nagar, Kattankulathur
VALLIAMMAI ENGINEERING COLLEGE SRM Nagar, Kattankulathur 603 203. DEPARTMENT OF ELECTRONICS & COMMUNICATION ENGINEERING SUBJECT QUESTION BANK : EC6405 CONTROL SYSTEM ENGINEERING SEM / YEAR: IV / II year
More informationSystems Analysis and Control
Systems Analysis and Control Matthew M. Peet Arizona State University Lecture 23: Drawing The Nyquist Plot Overview In this Lecture, you will learn: Review of Nyquist Drawing the Nyquist Plot Using the
More informationSTABILITY ANALYSIS TECHNIQUES
ECE4540/5540: Digital Control Systems 4 1 STABILITY ANALYSIS TECHNIQUES 41: Bilinear transformation Three main aspects to controlsystem design: 1 Stability, 2 Steadystate response, 3 Transient response
More informationEE C128 / ME C134 Fall 2014 HW 6.2 Solutions. HW 6.2 Solutions
EE C28 / ME C34 Fall 24 HW 6.2 Solutions. PI Controller For the system G = K (s+)(s+3)(s+8) HW 6.2 Solutions in negative feedback operating at a damping ratio of., we are going to design a PI controller
More informationR. W. Erickson. Department of Electrical, Computer, and Energy Engineering University of Colorado, Boulder
R. W. Erickson Department of Electrical, Computer, and Energy Engineering University of Colorado, Boulder 8.1. Review of Bode plots Decibels Table 8.1. Expressing magnitudes in decibels G db = 0 log 10
More information10ES43 CONTROL SYSTEMS ( ECE A B&C Section) % of Portions covered Reference Cumulative Chapter. Topic to be covered. Part A
10ES43 CONTROL SYSTEMS ( ECE A B&C Section) Faculty : Shreyus G & Prashanth V Chapter Title/ Class # Reference Literature Topic to be covered Part A No of Hours:52 % of Portions covered Reference Cumulative
More informationProportional plus Integral (PI) Controller
Proportional plus Integral (PI) Controller 1. A pole is placed at the origin 2. This causes the system type to increase by 1 and as a result the error is reduced to zero. 3. Originally a point A is on
More informationFREQUENCYRESPONSE ANALYSIS
ECE450/550: Feedback Control Systems. 8 FREQUENCYRESPONSE ANALYSIS 8.: Motivation to study frequencyresponse methods Advantages and disadvantages to rootlocus design approach: ADVANTAGES: Good indicator
More informationIntro to Frequency Domain Design
Intro to Frequency Domain Design MEM 355 Performance Enhancement of Dynamical Systems Harry G. Kwatny Department of Mechanical Engineering & Mechanics Drexel University Outline Closed Loop Transfer Functions
More informationAPPLICATIONS FOR ROBOTICS
Version: 1 CONTROL APPLICATIONS FOR ROBOTICS TEX d: Feb. 17, 214 PREVIEW We show that the transfer function and conditions of stability for linear systems can be studied using Laplace transforms. Table
More informationa. Closedloop system; b. equivalent transfer function Then the CLTF () T is s the poles of () T are s from a contribution of a
Root Locus Simple definition Locus of points on the s plane that represents the poles of a system as one or more parameter vary. RL and its relation to poles of a closed loop system RL and its relation
More informationLaplace Transform Analysis of Signals and Systems
Laplace Transform Analysis of Signals and Systems Transfer Functions Transfer functions of CT systems can be found from analysis of Differential Equations Block Diagrams Circuit Diagrams 5/10/04 M. J.
More informationLinear Control Systems Lecture #3  Frequency Domain Analysis. Guillaume Drion Academic year
Linear Control Systems Lecture #3  Frequency Domain Analysis Guillaume Drion Academic year 20182019 1 Goal and Outline Goal: To be able to analyze the stability and robustness of a closedloop system
More informationResponse to a pure sinusoid
Harvard University Division of Engineering and Applied Sciences ES 145/215  INTRODUCTION TO SYSTEMS ANALYSIS WITH PHYSIOLOGICAL APPLICATIONS Fall Lecture 14: The Bode Plot Response to a pure sinusoid
More informationRaktim Bhattacharya. . AERO 422: Active Controls for Aerospace Vehicles. Frequency ResponseDesign Method
.. AERO 422: Active Controls for Aerospace Vehicles Frequency Response Method Raktim Bhattacharya Laboratory For Uncertainty Quantification Aerospace Engineering, Texas A&M University. ... Response to
More informationDr Ian R. Manchester Dr Ian R. Manchester AMME 3500 : Review
Week Date Content Notes 1 6 Mar Introduction 2 13 Mar Frequency Domain Modelling 3 20 Mar Transient Performance and the splane 4 27 Mar Block Diagrams Assign 1 Due 5 3 Apr Feedback System Characteristics
More informationRoot Locus. Signals and Systems: 3C1 Control Systems Handout 3 Dr. David Corrigan Electronic and Electrical Engineering
Root Locus Signals and Systems: 3C1 Control Systems Handout 3 Dr. David Corrigan Electronic and Electrical Engineering corrigad@tcd.ie Recall, the example of the PI controller car cruise control system.
More informationModule 07 Control Systems Design & Analysis via RootLocus Method
Module 07 Control Systems Design & Analysis via RootLocus Method Ahmad F. Taha EE 3413: Analysis and Desgin of Control Systems Email: ahmad.taha@utsa.edu Webpage: http://engineering.utsa.edu/ taha March
More informationFrequency Response of Linear Time Invariant Systems
ME 328, Spring 203, Prof. Rajamani, University of Minnesota Frequency Response of Linear Time Invariant Systems Complex Numbers: Recall that every complex number has a magnitude and a phase. Example: z
More informationSTABILITY OF CLOSEDLOOP CONTOL SYSTEMS
CHBE320 LECTURE X STABILITY OF CLOSEDLOOP CONTOL SYSTEMS Professor Dae Ryook Yang Spring 2018 Dept. of Chemical and Biological Engineering 101 Road Map of the Lecture X Stability of closedloop control
More informationControl Systems I Lecture 10: System Specifications
Control Systems I Lecture 10: System Specifications Readings: Guzzella, Chapter 10 Emilio Frazzoli Institute for Dynamic Systems and Control DMAVT ETH Zürich November 24, 2017 E. Frazzoli (ETH) Lecture
More informationChemical Process Dynamics and Control. Aisha Osman Mohamed Ahmed Department of Chemical Engineering Faculty of Engineering, Red Sea University
Chemical Process Dynamics and Control Aisha Osman Mohamed Ahmed Department of Chemical Engineering Faculty of Engineering, Red Sea University 1 Chapter 4 System Stability 2 Chapter Objectives End of this
More informationECE382/ME482 Spring 2005 Homework 6 Solution April 17, (s/2 + 1) s(2s + 1)[(s/8) 2 + (s/20) + 1]
ECE382/ME482 Spring 25 Homework 6 Solution April 17, 25 1 Solution to HW6 P8.17 We are given a system with open loop transfer function G(s) = 4(s/2 + 1) s(2s + 1)[(s/8) 2 + (s/2) + 1] (1) and unity negative
More informationAsymptotic Bode Plot & LeadLag Compensator
Asymptotic Bode Plot & LeadLag Compensator. Introduction Consider a general transfer function Ang Man Shun 20225 G(s = n k=0 a ks k m k=0 b ks k = A n k=0 (s z k m k=0 (s p k m > n When s =, transfer
More informationEC 8391CONTROL SYSTEMS ENGINEERING. Questions and Answers PARTA. Unit  I Systems Components And Their Representation
EC 8391CONTROL SYSTEMS ENGINEERING Questions and Answers PARTA Unit  I Systems Components And Their Representation 1. What is control system? A system consists of a number of components connected together
More informationR10 JNTUWORLD B 1 M 1 K 2 M 2. f(t) Figure 1
Code No: R06 R0 SET  II B. Tech II Semester Regular Examinations April/May 03 CONTROL SYSTEMS (Com. to EEE, ECE, EIE, ECC, AE) Time: 3 hours Max. Marks: 75 Answer any FIVE Questions All Questions carry
More information(Refer Slide Time: 2:11)
Control Engineering Prof. Madan Gopal Department of Electrical Engineering Indian institute of Technology, Delhi Lecture  40 Feedback System Performance based on the Frequency Response (Contd.) The summary
More informationMAE 143B  Homework 9
MAE 143B  Homework 9 7.1 a) We have stable firstorder poles at p 1 = 1 and p 2 = 1. For small values of ω, we recover the DC gain K = lim ω G(jω) = 1 1 = 2dB. Having this finite limit, our straightline
More information(Continued on next page)
(Continued on next page) 18.2 Roots of Stability Nyquist Criterion 87 e(s) 1 S(s) = =, r(s) 1 + P (s)c(s) where P (s) represents the plant transfer function, and C(s) the compensator. The closedloop characteristic
More informationNADAR SARASWATHI COLLEGE OF ENGINEERING AND TECHNOLOGY Vadapudupatti, Theni
NADAR SARASWATHI COLLEGE OF ENGINEERING AND TECHNOLOGY Vadapudupatti, Theni625531 Question Bank for the Units I to V SE05 BR05 SU02 5 th Semester B.E. / B.Tech. Electrical & Electronics engineering IC6501
More informationEECS C128/ ME C134 Final Thu. May 14, pm. Closed book. One page, 2 sides of formula sheets. No calculators.
Name: SID: EECS C28/ ME C34 Final Thu. May 4, 25 58 pm Closed book. One page, 2 sides of formula sheets. No calculators. There are 8 problems worth points total. Problem Points Score 4 2 4 3 6 4 8 5 3
More informationControl Systems. EC / EE / IN. For
Control Systems For EC / EE / IN By www.thegateacademy.com Syllabus Syllabus for Control Systems Basic Control System Components; Block Diagrammatic Description, Reduction of Block Diagrams. Open Loop
More informationAnalysis of SISO Control Loops
Chapter 5 Analysis of SISO Control Loops Topics to be covered For a given controller and plant connected in feedback we ask and answer the following questions: Is the loop stable? What are the sensitivities
More informationControl Systems. University Questions
University Questions UNIT1 1. Distinguish between open loop and closed loop control system. Describe two examples for each. (10 Marks), Jan 2009, June 12, Dec 11,July 08, July 2009, Dec 2010 2. Write
More informationR a) Compare open loop and closed loop control systems. b) Clearly bring out, from basics, Forcecurrent and ForceVoltage analogies.
SET  1 II B. Tech II Semester Supplementary Examinations Dec 01 1. a) Compare open loop and closed loop control systems. b) Clearly bring out, from basics, Forcecurrent and ForceVoltage analogies..
More informationTable of Laplacetransform
Appendix Table of Laplacetransform pairs 1(t) f(s) oct), unit impulse at t = 0 a, a constant or step of magnitude a at t = 0 a s t, a ramp function e at, an exponential function s + a sin wt, a sine fun
More informationLABORATORY INSTRUCTION MANUAL CONTROL SYSTEM I LAB EE 593
LABORATORY INSTRUCTION MANUAL CONTROL SYSTEM I LAB EE 593 ELECTRICAL ENGINEERING DEPARTMENT JIS COLLEGE OF ENGINEERING (AN AUTONOMOUS INSTITUTE) KALYANI, NADIA CONTROL SYSTEM I LAB. MANUAL EE 593 EXPERIMENT
More informationFREQUENCYRESPONSE DESIGN
ECE45/55: Feedback Control Systems. 9 FREQUENCYRESPONSE DESIGN 9.: PD and lead compensation networks The frequencyresponse methods we have seen so far largely tell us about stability and stability margins
More information